Hi,

Currently, when driving the NDLR from an external sequencer, the NDLR disarms all the parts when it handles a MIDI stop message. I'm finding it a bit frustrating as I have to remember to re-arm the particular parts when re-starting the sequencer. Could we have the option so the NDLR doesn't do this? It should still do everything else it does on a stop message (e.g. release any held notes on all parts), just leave the arm state of each part alone.

Cheers,

Ian

There is no way to alter the velocity of the drone. 
Is there anything that could be done about that ? 
Thanks

This only applies to MOTIF tracks. 

Yes we can create new rhythmic patterns where we use the TIEs to make the NOTE-ON/OFF interval longer. I’m already running out of slots doing that.

What would really help is to double the humanize range from 1-10 to 1-20 with the second half randomizing Note duration too. 
so values 1-10 would still do Velocity/Timing (Not sure if timing is there already) 
and values 11-20 would add note duration randomization with focus to shorten notes rather than make them longer.  

....Another option would be to add a new destination called "Note length” to MOTIF sections ...But that would take 2 of precious slots
away. 

Thanks!

I know Darryl said that the NDLR chip has some limitations with memory when I asked  to save more than 8 “System" setups 
I’m not sure if “teensy” is on a separate board inside of the NDLR. If yes then we could just pop-in a more powerful teensy board.  
If teensy is on the main PCB then I would pay (kickstarter) for “upgrade” to better CPU with more memory. SO we can get less latency when using as MIDI THRU and get more setup slots. And I would call them session slots. 

Also the setup slots could be alphanumeric (yes I know more bytes per slot) so I can have them as SONGS or sessions. 

How about having "floating storage boundaries"  for the biggest memory consumers: rhythmic pattern, melody pattern, setup slots
For example I hardly use melodic patterns, But I do a lot of rhythmic patters so I could use more memory for rhythms and setup slots) 

Thanks!

Since I’m having trouble to control Chord type/degree from external Keyboard with newest firmware I came with alternate cool method for NDLR to play two chords automatically: 

1. Pick a mod slot and set it to 8 or 16 bars Square 
2. Set destination to the chord degree
3. Set the range to go between 1-IV (0-2 or C<->F in C major) 
4. Set the drone trigger to be chord based type (follows the chord degree) and activated on the first 1/4 note)  
5. turn on PAD,DROne and perhaps one Motif
6. The chord degree changes every 4/8 bars and Motif and Pad play nice changing degree

BUT!t The Drone is delayed by half of bar with the chord note change
Bug or desired behavior or I don’t know what I’m doing 

The desired behavior is that all 4 parts change the chord degree at the same time

thanks!

I set up a pad and a drone on the NDLR (running the shipped OS, not beta - my Mac is at 10.6.8, so have to do the upgrade on my Windows machine later, but I digress...).

The pad and drone MIDI channels are the same (triggering an MKS-20).  Drone is set to chord mode, all empty boxes.
Tempo is set to 72, Pad quantization set to 1/4 note.
If I start the Drone running and press a key on my external MIDI controller (a PPG - don't ask), I immediately hear the Drone triggered.
If I stop the Drone and start Pad and trigger it, I can hear the start being quantized to the quarter note.  It's especially noticeable if I have both Drone and Pad on - you can hear one triggering later than the other for most key presses.

Is the Drone supposed to be independent like that?

Hi, I am struggling with that to setup , somehow or doing something wrong or even maybe misunderstand the whole thing of it.

MIDI channel for NDLR Control worked out and is really cool.

I have a MIO10 midi patchbay an use the Elektron Analog Key (AK) with its external keyboard mode and set the xternal channel to 16.
NDLR sends a out all on MIDI A and the patchbay send all incoming to the other synths.

Using channel 15 for NDLR ctrl on the AK in external mode and depening on what white or black keys i pressed it changed it chords and degrees.

On the other hand with channel set to 16 I do not hear any transpose going on , nor something played from the notes I pressed on the keyboard ?


Any advise or example ? need more info about my setup ?

br Thorsten

That's some phat filter for $199 USD.

Behringer Crave playlist on YouTube.

Hi,
looking for info on what the dimension of the screws to get for mounting sides on the NDLR. What about the threads(Is there a DIN-number?) and depth of the screw?

Hope someone here knows...

Regards

Hi ,
can you implement something like a srceensaver for the OLED ? Something like :

if for 10 sec no input has been done on knobs or encoders reduce the brilliance and after 60 sec turn of the display and maybe have settings for these 2 stages .

Advantage  longer live for the OLED and reducing the burn-in off ghosting.

br Thorsten