I have a usb midi device called the phantasmal force I've successfully used with my mrcc for quite some time. They recently came out with a new firmware for the device and after installing the firmware it immediately locks up the mrcc. I can plug the PF into several other midihosts such as op1 field, my PC, the retrokits rk-6 and it works great with all of those but the mrcc is not happy. If I plug it into one of the 4 usb ports after the mrcc is running the mrcc will provide power to the various connected devices and all it's leds stay on and all connected devices stay powered but the mrcc screen is unresponsive and iit no longer appears to be processing any incoming or outgoing midi. If I start up the mrcc with the PF already plugged into a usb port the leds chase about halfway on the mrcc and the mrcc just hangs there. How can I try to troubleshoot this further. I really need the PF to use one of the usb ports in this case because of how messages are routed to the other devices. While the PF can send midi over trs I need to use usb midi to use an external clock. Please let me know what is a good next step to begin sorting out this issue. It is a usb midi compliant device and it uses an M0 arm processor with Uf2 bootloader. I tried unplugging many of the other devices on the mrcc and removing any midi routings to and from the port and I tried other usb ports too but the response is the same.

Sorry if this has already been covered (I'm new to the NDLR I couldn't find out).

Can a chord that's not in the key of the song be used to replace a current one?  For example we play a song in the key of B but there's also a A major in there too.  If this is possible - can it then be saved as a preset as such?

Thank you for any info.

Hi.

On settings page 1 I set the mrcc midi control channel to p11 but when I turn the MRCC back on next day it has reverted to the dash symbol, it's a long way to keep scrolling every day...

Any ideas?

Thanks.

OS=1.1.075

It would be cool to be able to move the play range anywhere inside patterns & rythms.

While I was using an external controller to control the NDLR, I just thought that it would be cool to have a CC dedicated to switch between menus?

Hi,

I'm having trouble understanding the CC message filtering on the routing page? The manual states you can filter CC messages, and according to appendix C in the manual, it seems that only CC11 is filtered; is this correct or am I reading this wrong?



Thanks

New owner of an MRCC 880 here. I'm pretty new to MIDI workflows and I can't the get the MRCC 880 to receive Midi note data from my Keystep 37. It receives and sends data from my Roli Seaboard Block M just fine, but nothing registers from the Keystep. I know the Keystep is sending midi data, as indicated both from Ableton and from Arturia's midi control center. I've double checked the 5-pin din cable and it works fine when sending midi out of the Keystep directly into my desktop Hydrasynth. However, when I try and route through the MRCC 880, I get nothing.

Can anyone shed some light on why these two devices aren't communicating?

Big thanks in advance for anyone willing to assist,

Stephen

Hey, Hi! You folks know me as Jesse, the support team of Conductive Labs, but I also am the owner of a small Eurorack manufacturer called Altered State Machines. We have a few modules, one of which, the Aristotle sequencer, was recently highlighted by YouTuber Tom Churchill and it seems like a lot of people were inspired by his video and they've been flying off the shelves. I just wanted to share my excitement a little bit here, and if any of you would like to have a look I will link the video as well.

Dear ConductiveLabs Team,

I want to cut side panels for the NDLR, and could use some specs. Would / could you please make a technical drawing with measurements, radius, and angles available for download?


Thank you

Melkor

Hello there,
I have been using the NDLR for a few months now, and I really enjoy all of the creative possibilities it offers. I am gearing up for some live performances and want to make sure I am fully optimizing its capabilities in a live setting.

My current setup includes a MIDI keyboard, a couple of synths, & a drum machine. I have been primarily using the NDLR to generate complex sequences & arpeggios but I am curious about how others are integrating it into their live workflows.

Seamless transitions between patterns and motifs during a live set
I want to know Best practices for syncing the NDLR with other MIDI devices
Any recommended settings or features that shine in a live environment
How to quickly adapt or tweak sequences on the fly without disrupting the flow

Also i have read this resorse/artical; https://conductivelabs.com/forum/showthr...JQXtKZr4IQampscript-in-sfmc but have not found any solution still need your advice. if you have any advice, insights, experiences or even setup suggestions would be greatly appreciated.

Thank you